Lesson 10 – Responder
Tutorial
1. Introduction
In this experiment, we make a further learning on the basis of lesson 6. We use four buttons to control three LEDs, making a responder.
2. Hardware Required
- LED – Red *1
- LED – Blue*1
- LED – Yellow*1
- 220Ω Resistor*3
- Large Button Switch *4
- 10KΩ Resistor*4
- RPI GPIO Shield*1
- 40Pin Colorful Ribbon Cable *1
- Breadboard*1
- USB Cable*1
- Raspberry Motherboard*1
- Jumper Wires*Several
3. Connection Diagram
4. Programming
- a. Use winSCP to put the lesson9_Responder into the lesson folder of raspberry system.
b. In the terminal input cd lesson9_Responder to enter the folder.
c. In the terminal execute make, to generate a Responder executable file inside the folder.
d. Wiring as the above diagram, then enter the lesson9_Responder folder, execute sudo ./Responder at the terminal. Press the corresponding button to control the LED, so it is equivalent to a responder.
e. Ctrl + c can exit the processing program.
5. Sample Code
The first four lines below are –
- #include <stdio.h>
- #include <stdlib.h>
- #include <stdint.h>
- #include <wiringPi.h>
#include
#include
#include
#include
int redled=25; // set red LED as “output”
int yellowled=24; // set yellow LED as “output”
int blueled=23; // set blue LED as “output”
int redpin=4; // initialize pin for red button
int yellowpin=5; // initialize pin for yellow button
int bluepin=6; // initialize pin for blue button
int restpin=1; // initialize pin for reset button
int red;
int yellow;
int blue;
void clear_led()// all LED off
{
digitalWrite(redled,LOW);
digitalWrite(blueled,LOW);
digitalWrite(yellowled,LOW);
}
void RED_YES()// execute the code until red light is on; end cycle when reset button is pressed
{
while(digitalRead(restpin)==1)
{
digitalWrite(redled,HIGH);
digitalWrite(blueled,LOW);
digitalWrite(yellowled,LOW);
}
clear_led();
}
void YELLOW_YES()// execute the code until yellow light is on; end cycle when reset button is pressed
{
while(digitalRead(restpin)==1)
{
digitalWrite(redled,LOW);
digitalWrite(blueled,LOW);
digitalWrite(yellowled,HIGH);
}
clear_led();
}
void BLUE_YES()// execute the code until green light is on; end cycle when reset button is pressed
{
while(digitalRead(restpin)==1)
{
digitalWrite(redled,LOW);
digitalWrite(blueled,HIGH);
digitalWrite(yellowled,LOW);
}
clear_led();
}
int main()
{
wiringPiSetup();
{
pinMode(redled,OUTPUT);
pinMode(yellowled,OUTPUT);
pinMode(blueled,OUTPUT);
pinMode(redpin,INPUT);
pinMode(yellowpin,INPUT);
pinMode(bluepin,INPUT);
}
while(1)
{
red=digitalRead(redpin);
yellow=digitalRead(yellowpin);
blue=digitalRead(bluepin);
if(red==LOW)RED_YES();
if(yellow==LOW)YELLOW_YES();
if(blue==LOW)BLUE_YES();
}
}
Prerequisites
- This development track is based on the Rasbperry Pi and the Ultimate Starter Kit for the Raspberry Pi.
- You will need access to both the Raspberry Pi SBC and the electronics components part of the Ultimate Starter Kit for the Raspberry Pi kit to be able to work on these tutorials.
- If you haven’t purchased the Raspberry Pi 4 B yet please head over to our store and purchase one now. You can pick up the Ultimate Starter Kit for the Raspberry Pi from OztoyLib.
- Depending on where you live you might also be able to pick up the Raspberry Pi and Ultimate Starter Kit for the Raspberry Pi at your local electronics hobby store.
About the Ultimate Starter Kit for the Raspberry Pi
The Ultimate Starter Kit for the Raspberry Pi comes packed with ~37 different electronic bits (Sensors, LEDs, switches, LCD, servo, etc.) including tutorials to get started. You will learn how to connect up the ~37 different electronic bits (Sensors, LEDs, switches, LCD, servo, etc.), create circuits using the Raspberry Pi including learning to write code in C. As you progress through the different tutorials you will explore the different capabilities of the Raspberry Pi including the intricacies of integrating the Raspberry Pi with the different electronic bits i.e. sensors, LED’s, switches, servos, etc. included in the starter kit.
The Ultimate Starter Kit for the Raspberry Pi comes along with detailed tutorials including code samples. Ultimate Starter Kit for the Raspberry Pi walks you through the basics of using the Raspberry Pi in a hands-on way. You’ll learn the fundamentals of electronics, programming in C and gain hands on experience through working on the Raspberry Pi building creative projects. The kit includes a selection of the most common and useful electronic components with an ebook of 37 projects. Starting the basics of electronics, to more complex projects, the kit will get you interacting with the physical world using sensor and actuators. Along with the kit you get access to detailed tutorials and wiring diagrams.
About the Raspberry Pi
The Raspberry Pi is a series of small single-board computers developed in the United Kingdom by the Raspberry Pi Foundation to promote the teaching of basic computer science in schools and in developing countries. It is a capable little computer which can be used in electronics projects, and for many of the things that your desktop PC does, like spreadsheets, word processing, browsing the internet, and playing games. The original model became far more popular than anticipated, selling outside its target market for uses such as robotics.
The Raspberry Pi does not include peripherals (such as keyboards, mice and cases). However, some accessories have been included in several official and unofficial bundles. According to the Raspberry Pi Foundation, over 5 million Raspberry Pis were sold by February 2015, making it the best-selling British computer. By November 2016 they had sold 11 million units, and 12.5m by March 2017, making it the third best-selling “general purpose computer”. In July 2017, sales reached nearly 15 million.In March 2018, sales reached 19 million. Most Pis are made in a Sony factory in Pencoed, Wales; some are made in China or Japan.
You can read more about the Raspberry Pi here – RaspberryPi.org.
